In daily use, the rotary feeder should pay more attention to the dust being blocked when it strikes in the ash hopper or falls into rigid materials, so as to avoid damaging the operating equipment. The abrasive dust impeller is quickly worn, and the impeller should be timely repaired. Feeder is a widely used product. Most of the problems will occur in the actual use process. I have summarized several common problems that will occur in the work process.

供料器适用于连续正反运转，在运行过程中假如发生沿轴向漏风或是漏灰现象，可禁锢压料盖的螺丝或是重新更换石棉盘根后再压紧料盖即可。供料器在出厂前需要注足润滑油与润滑脂，在使用6个月后，传动及轴承部位应增补或是更换油脂，假如安装环境的温度较高或是灰尘过多，都应缩短换油时间。

The feeder is suitable for continuous positive and negative operation. In case of axial air leakage or ash leakage during operation, the screw of the pressing cover can be fastened or the asbestos packing can be replaced and then the material cover can be pressed tightly. The feeder shall be fully filled with lubricating oil and grease before delivery. After 6 months of use, the transmission and bearing parts shall be supplemented or replaced with grease. If the temperature of the installation environment is high or there is too much dust, the oil change time shall be shortened.

旋转供料器是除尘器密封卸料的专用装置，它能连续不断的排料及把物料输送到指定装置内，对多种物料均可应用。耐温型供料器所输送物料的温度可达280℃，两端轴承与叶轮有一定隔离，能防止超细粉料与轴承接触。耐高温型供料器输送物料的温度高达500℃，采用链轮连接，减速机和卸料器壳体有一定的间隔。

The rotary feeder is a special device for sealing and unloading of the dust remover. It can continuously discharge and transport materials to the designated device, and can be used for a variety of materials. The temperature of the materials conveyed by the temperature resistant feeder can reach 280 ℃. The bearings at both ends are isolated from the impeller to prevent the contact between the ultra-fine powder and the bearing. The high temperature resistant feeder conveys materials at a temperature of up to 500 ℃, which is connected by chain wheels. There is a certain distance between the reducer and the discharger shell.

供料器的特点：

Features of feeder:

1、配用摆线轮减速机，结构紧凑，不乱可靠。

1. Equipped with cycloidal gear reducer, the structure is compact and reliable.

2、采用弹性叶轮、增强柔性密封，叶轮卡住现象。

2. Elastic impeller and enhanced flexible seal are adopted to eliminate the seizure of impeller.

3、轴承座移位阀体外侧，隔断尘粒直接来源，延长轴承使用寿命，利便维修。

3. The bearing seat is displaced outside the valve body to isolate the direct source of dust particles, prolong the service life of the bearing and facilitate maintenance.

以上就是为大家介绍的有关广东旋转供料器的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sddyfd.com/

The above is a detailed introduction to Guangdong rotary feeder, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://www.sddyfd.com/